PXE boot on ipv4 boot problem in Windows

We have all had computer problems. It can be really annoying when the well-functioning computer suddenly starts throwing up error messages. Some of these errors can be ignored, while others can make your computer unusable. Our website is dedicated to addressing these issues and today we are going to take a look at the persistent “Start PXE over IPv4” error message.

In this article, we will tell you all about this error, including how it is caused and how to fix it should you encounter it. The solutions are quite simple to follow. Let’s get started.

What is the “Start PXE over IPv4” boot problem in Windows 10?

For readers who have never encountered it, this error occurs at Windows startup. It occurs when the computer tries to boot using the PXE option and not from the hard drive. There may be several reasons for this to occur. One of the most common reasons is that the hard drive has failed and the computer cannot find any other boot devices. Since PXE is used to configure and boot network computers that do not yet have an operating system, the computer uses PXE as an alternative. Another common reason for the Start PXE over IPv4 message is to give PXE the highest boot priority.

It can also be caused by an outdated BIOS, a failed Windows update, or after installing a secondary storage device. Whatever the reason, we will give you all the methods you can use to say goodbye to this irritating message.

YOU CAN ALSO READ:   Repair 0xc000021a Error in Windows 10, 8 and 7

Methods to fix Start PXE over IPv4

These methods are written in no particular order. Since there are different reasons for this problem, we recommend that you read it all and find the solution that specifically addresses your problem. Let us begin.

Method 1: Correct the boot priority order

“Start pxe over ipv4” occurs when your boot device is not configured correctly. It would be below the PXE option in the boot priority order. This can usually be bypassed by pressing the Esc key, but the fact is that it doesn’t solve the problem. If you only see this error message when you have an Ethernet cable plugged in at startup, and not always using WiFi, you can be sure it is a boot priority issue. To fix this, all you have to do is follow these simple steps.

The steps:

  1. Turn off your computer. Turn it back on and press the setup key several times. It is different on different devices, but you can see the setup key on the screen as soon as your device starts to boot into BIOS setup. If you cannot find the correct key, check the Internet to find the correct key for your device. The length of time allowed to press this key is quite short, so press it as fast as you can. Note that if you can already find the Boot tab, you can proceed to step 6.
  2. Use the arrow keys to go to the Security tab. Then select the Safe Boot Settings option from the menu.
  3. Use the arrow keys again to change the Safe Start value. See the instructions given in the menu to change the value from On to Off.
  4. Now set legacy support to enabled. Save and exit.
  5. Restart your computer and go back to BIOS setup. If you are prompted to enter a code, please do so. Restart your computer and go back to BIOS setup.
  6. Select the Boot menu tab with the arrow keys. Change the order of priority making sure the boot device is at the top of the list. Instructions for doing this will be displayed in the BIOS menu.
  7. Save and exit and restart your computer again. This time you will not be able to see the Start PXE over IPv4 error message.
YOU CAN ALSO READ:   User Profile Repair Service failed to log into Windows 10

If this doesn’t fix your problem, we have another solution to help you. You can disable Wake on LAN in BIOS setup. You can find those settings in the Power menu or the Advanced Settings menu, depending on the manufacturer. This should solve your problem.

Method 2: Change the boot device

If your boot device (HDD or SSD) has failed, the computer will fall back to PXE no matter what the priority of the boot order is. The best course of action would be to run a diagnostic test first and then confirm if your storage device is at fault here. You have to watch:

  1. Clicking noises if you are using a hard drive.
  2. Random accidents.
  3. The computer does not start sometimes.

If these are your problems, you may need to change your boot device entirely.

Method 3: Update the BIOS

Many problems like this can arise from a Outdated or corrupted BIOS . You can update it yourself and the problems will probably go away. Just follow the instructions in this video to get a clear picture.

YOU CAN ALSO READ:   Windows 10 reopens apps and Windows after restart

Final take

These are all the available methods you can use to solve this annoying “boot pxe over ipv4” problem. Hopefully one of these methods worked for you and now you can turn on your computer without any worries. However, keep in mind that if none of these methods work, you may need to take it to your device’s service center. If you have any other suggestions or concerns, let us know in the comment section and we will get back to you.

Leave a Reply

Your email address will not be published. Required fields are marked *